Comments for HACKMIAMI http://hackmiami.org Tue, 23 Feb 2010 23:52:51 +0000 http://wordpress.org/?v=2.9.1 hourly 1 Comment on Magnetic Stripe Card Reader! by nitroboozter http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-1374 nitroboozter Tue, 23 Feb 2010 23:52:51 +0000 http://hackmiami.org/blog/?p=16#comment-1374 hey i have also changed the pin numbers in the program too hey i have also changed the pin numbers in the program too

]]> Comment on Magnetic Stripe Card Reader! by nitroboozter http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-1373 nitroboozter Tue, 23 Feb 2010 23:51:19 +0000 http://hackmiami.org/blog/?p=16#comment-1373 hey can you please check if the connections in the diagram and the program's pin connection are all correct.i have an ARDUINO MEGA and i tried connecting all the pins in the sanguino to the respective pins in the mega i am using a OMRON 3S4YR-SBR4N-50 manual half insert reader the connections i made are correct i checked it two three times OMRON PIN DETAIL FROM DATASHEET not connected -- pin1 read data (output) -- pin2 read clock (output) -- pin3 card load (output) -- pin4 card detection rear(output) -- pin5 card detection rear(input) -- pin6 card detection front(output) -- pin7 card detection front(input) -- pin8 vin -- pin9 ground -- pin10 ARDUINO MEGA PIN DETAIL pin1 -- connected to omron pin2 pin2 (interrupt 0)-- connected to omron pin5 pin3 (interrupt 1)-- connected to omron pin3 pin21(interrupt 2)-- connected to omron pin4 i have not connected any lcd and have removed all the codings for the lcd..when i've hooked it up the pc and check for the data using serial monitor all i get is Raw: and 2-3 line of spaces when i insert and remove a card.please tell me what i'm doing wrong??? hey can you please check if the connections in the diagram and the program’s pin connection are all correct.i have an ARDUINO MEGA and i tried connecting all the pins in the sanguino to the respective pins in the mega i am using a OMRON 3S4YR-SBR4N-50 manual half insert reader the connections i made are correct i checked it two three times

OMRON PIN DETAIL FROM DATASHEET
not connected — pin1
read data (output) — pin2
read clock (output) — pin3
card load (output) — pin4
card detection rear(output) — pin5
card detection rear(input) — pin6
card detection front(output) — pin7
card detection front(input) — pin8
vin — pin9
ground — pin10

ARDUINO MEGA PIN DETAIL
pin1 — connected to omron pin2
pin2 (interrupt 0)– connected to omron pin5
pin3 (interrupt 1)– connected to omron pin3
pin21(interrupt 2)– connected to omron pin4

i have not connected any lcd and have removed all the codings for the lcd..when i’ve hooked it up the pc and check for the data using serial monitor all i get is Raw: and 2-3 line of spaces when i insert and remove a card.please tell me what i’m doing wrong???

]]> Comment on Post-Apocalyptic Communications by VS http://hackmiami.org/2009/10/06/post-apocalyptic-communications/comment-page-1/#comment-1369 VS Tue, 23 Feb 2010 16:50:32 +0000 http://hackmiami.org/?p=151#comment-1369 that would be awesome, actually i was just about to email you. could you by any chance e-mail me the article? that would be awesome, actually i was just about to email you. could you by any chance e-mail me the article?

]]> Comment on Post-Apocalyptic Communications by jp http://hackmiami.org/2009/10/06/post-apocalyptic-communications/comment-page-1/#comment-1368 jp Tue, 23 Feb 2010 16:41:46 +0000 http://hackmiami.org/?p=151#comment-1368 One of these days... One of these days…

]]> Comment on Post-Apocalyptic Communications by VS http://hackmiami.org/2009/10/06/post-apocalyptic-communications/comment-page-1/#comment-1367 VS Tue, 23 Feb 2010 16:31:22 +0000 http://hackmiami.org/?p=151#comment-1367 Seriously how about posting the article Seriously how about posting the article

]]> Comment on Magnetic Stripe Card Reader! by sarun http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-1098 sarun Tue, 15 Dec 2009 15:10:18 +0000 http://hackmiami.org/blog/?p=16#comment-1098 the above program will not work for arduino decimila or duemilanove because the program uses 3 interrupts which both the arduino's don't have [they have only 2 interrupts] the above program will not work for arduino decimila or duemilanove because the program uses 3 interrupts which both the arduino’s don’t have [they have only 2 interrupts]

]]> Comment on Post-Apocalyptic Communications by peter (NOT pete) http://hackmiami.org/2009/10/06/post-apocalyptic-communications/comment-page-1/#comment-1087 peter (NOT pete) Mon, 14 Dec 2009 00:51:45 +0000 http://hackmiami.org/?p=151#comment-1087 congrats on the article. i thought about writing one posed as a riddle/hacking exercise. i'd set it up with all the basic information about the hole in question and they'd have to go out and see what it applied to... promote people exploring security in the real world. incidentally, they have The Best Of 2600 in bookstores now. some of that stuff (like Simplex locks - lulz) i had totally forgotten about congrats on the article. i thought about writing one posed as a riddle/hacking exercise. i’d set it up with all the basic information about the hole in question and they’d have to go out and see what it applied to… promote people exploring security in the real world.

incidentally, they have The Best Of 2600 in bookstores now. some of that stuff (like Simplex locks – lulz) i had totally forgotten about

]]> Comment on Magnetic Stripe Card Reader! by spatialguru http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-843 spatialguru Thu, 26 Nov 2009 06:03:17 +0000 http://hackmiami.org/blog/?p=16#comment-843 Any tips on getting custom card blanks and a writer? It can't be _that_ hard can it? ;) Any tips on getting custom card blanks and a writer? It can’t be _that_ hard can it? ;)

]]> Comment on Magnetic Stripe Card Reader! by Jaime http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-547 Jaime Thu, 29 Oct 2009 21:03:52 +0000 http://hackmiami.org/blog/?p=16#comment-547 Can you give-me some direction to start pls the idea that i have is like this: have a LCD saying (Please Pass Card) (Invalid Card){When the card of a non authorized worker try to use the machine} (Machine ON) (Out of Service) I thinking to use the card reader a LCD and a relay to start the machine. My Arduino is going to arrive in 1 day to start the tests if you can point me in the right direction i will be very happy because I'm only starting to learn who to use this now. I have seen that the part of LCD and relay is not very difficult but card reader i think that is not so easy... TKS Jaime Branco Can you give-me some direction to start pls the idea that i have is like this:
have a LCD saying (Please Pass Card) (Invalid Card){When the card of a non authorized worker try to use the machine} (Machine ON) (Out of Service)
I thinking to use the card reader a LCD and a relay to start the machine.

My Arduino is going to arrive in 1 day to start the tests if you can point me in the right direction i will be very happy because I’m only starting to learn who to use this now. I have seen that the part of LCD and relay is not very difficult but card reader i think that is not so easy…

TKS

Jaime Branco

]]> Comment on Magnetic Stripe Card Reader! by jp http://hackmiami.org/2008/12/21/magnetic-stripe-card-reader/comment-page-1/#comment-546 jp Thu, 29 Oct 2009 16:25:14 +0000 http://hackmiami.org/blog/?p=16#comment-546 There is some modification to be done in order to get it to work with that Arduino and card reader. But it is definitely possible. I plan to revisit this project and make a non breadboard version of it. There is some modification to be done in order to get it to work with that Arduino and card reader. But it is definitely possible.

I plan to revisit this project and make a non breadboard version of it.

]]>